Wolf Sub-Zero 424FS Guía de instalación

INSTALLATION GUIDEWine Storage

Models 424 and 424FS Installation 10Lock InstallationIMPORTANT NOTE: If you are adding an accessory lock kitto your wine storage unit, it should be in

Level the UnitUsing an adjustable wrench or pliers, turn each of the fourleveling legs clockwise to raise the unit and counterclock-wise to lower the

Kickplate InstallationOnce the unit is leveled and wiring connections made,the kickplate can be installed. Use the two #10 x1/2"stainless steel s

Overlay Door Panel—Model 424Inspect the door panel for the minimum5/8"(16) thickness,the finished inside edge. The glass door has a 10 lbs (5 kg)

Models 424 and 424FS Installation 14Overlay Door Panel—Model 424IMPORTANT NOTE: Install screws in all the mountingholes in the door frame. The nature

Hinge AdjustmentIMPORTANT NOTE: The wine storage unit must beinstalled and leveled before door hinge adjustments canbe made.The top and bottom cabinet

Models 427 and 427R Installation 16Models 427 and 427ROVERALL DIMENSIONSMODEL 427 MODEL 427RWITH REFRIGERATOR DRAWERS27" (686)14"(356)13/16&

Models 427 and 427R Installation 17subzero.comModels 427 and 427R InstallationRefer to the previous page for overall dimensions anddoor swing clearanc

Models 427 and 427R Installation 18Electrical RequirementsFor models 427 and 427R, the electrical supply should belocated within the shaded area shown

Models 427 and 427R Installation 19subzero.comElectrical RequirementsHOME ALARM SYSTEMIf a home alarm system is to be used, refer to wiringconnections

Important NoteTo ensure the safe and efficient installation of Sub-Zeroequipment, please take note of the following types ofhighlighted information th

Models 427 and 427R Installation 20Anti-Tip Bracket InstallationAn anti-tip bracket and hardware is provided with the winestorage unit. The anti-tip b

Models 427 and 427R Installation 21subzero.comPosition UnitIMPORTANT NOTE: For model 427R, the top drawer has acontrol cable that needs to be disconne

Lock InstallationFor models 427 and 427R, the optional lock is attachedto the decorative door panel through a field-drilled hole inthe panel. The catc

LevelingLevel the unit by turning the front leveling legs clockwiseto raise the unit, or counterclockwise to lower it. To assistyou in adjusting the f

Models 427 and 427R Installation 24Wiring ConnectionsBefore the kickplate/grille is installed, all necessary wiringconnections in the compressor compa

Door PanelsModels 427 and 427R have a full-view glass door. Each ofthese wine storage units are set up at the job site as eitherthe stainless steel or

Models 427 and 427R Installation 26Stainless Steel Door PanelBefore installing the stainless steel door panel, check thepanel carefully. Options are a

Models 427 and 427R Installation 27subzero.comOverlay Door PanelThe screw holes inside the door are hidden under a coverflap on the door gasket. It is

Models 427 and 427R Installation 28Model 427R Drawer PanelsIMPORTANT NOTE: Drawer panels for model 427R mustbe a minimum of5/8" (16) thick and ca

Models 427 and 427R Installation 29subzero.comSide PanelsSide panels for models 427 and 427R are not attached tothe unit. You must securely fasten the

Wine Storage Equipment 3subzero.comWine Storage EquipmentThe importance of the installation of the Sub-Zero winestorage unit cannot be overemphasized.

Model WS-30 Installation 30Model WS-30 InstallationMake sure that the actual equipment that was shipped toyou matches the design you are expecting to

Model WS-30 Installation 31subzero.comTOOLS AND MATERIALS REQUIRED:• Phillips screwdriver set• Slotted screwdriver set• Torx drive screwdriver set• Le

Model WS-30 Installation 32Standard Installation Opening DimensionsFramed, Overlay and Stainless Steel ModelsIMPORTANT NOTE: If two units are installe

Model WS-30 Installation 33subzero.comFlush Inset Installation Opening DimensionsIMPORTANT NOTE: Dimensions assume a3/4" (19) panelthickness.IMPO

Model WS-30 Installation 34Opening Widths ATwo 30" (762) Models 593/4" (1518)Model WS-30 and a 36" (914) Model 653/4" (1670)IMPORT

Model WS-30 Installation 35subzero.comOpening Widths ABTwo 30" (762) Models 593/4" (1518) 621/4" (1581)Model WS-30 and a 36" (914)

Model WS-30 Installation 36Electrical RequirementsFor model WS-30, the electrical supply should be locatedwithin the shaded area shown in the illustra

Model WS-30 Installation 37subzero.comGrille removal. Grille mounting screws.FRONTGRILLE SCREWBACK GRILLESCREWLOCATIONOF GRILLEADJUSTMENTSCREWSUnpack

Model WS-30 Installation 38IMPORTANT NOTE: Placement of the anti-tip brackets iscritical to a stable installation. Failure to properly positionthe ant

Model WS-30 Installation 39subzero.comAnti-Tip Bracket InstallationCONCRETE FLOOR APPLICATIONSAfter properly locating the anti-tip brackets in the rou

Models 424 and 424FS Installation 4Door swing clearances are based on stainless steel door andhandle dimensions.237/8" (606) 24" (610)34&quo

Level the UnitOnce the unit is in position, extend the front leveling legsdown by turning the legs clockwise to adjust the height.The rear height adju

Model WS-30 Installation 41subzero.comUPPERHINGE BOLTSUpper hinge bolts. Door adjustment bolts.SIDE TO SIDETILT ADJUSTMENTIN AND OUTADJUSTMENTDoor hei

Home Alarm ConnectionsIf a home alarm system is to be installed on the winestorage unit, the connections should be made using thelogic supplied with t

Model WS-30 Installation 43subzero.comPanel InstallationBefore you install the front panel, refer to panel specifica-tions for framed, overlay or flus

FRAMED PANEL INSTALLATIONTo install the framed panel, the door handle must beremoved. To install framed panels, first remove the doortrim molding. Ins

Model WS-30 Installation 45subzero.comFramed PanelRAISED PANELWith some door panel designs, you may have to rout,recess or use optional extended handl

Model WS-30 Installation 46Overlay PanelsIf your customer has chosen an overlay design applica-tion, make sure that the panels you are about to instal

Model WS-30 Installation 47subzero.comOverlay PanelsGRILLE PANEL ASSEMBLYRemove the grille panel assembly as described on page37. Remove the top two c

Model WS-30 Installation 48Flush Inset PanelsIf your customer has chosen the flush inset panel applica-tion, make sure that the panels you are about t

Model WS-30 Installation 49subzero.comFlush Inset PanelsRemove the grille panel assembly as described on page37. Remove the top two corner screws and

Models 424 and 424FS Installation 5subzero.comModels 424 and 424FS InstallationThe model 424FS wine storage unit is designed to beattractive in a stan

Model WS-30 Installation 505/8"(16)55/16" (8)1/2"(13)FLUSH INSET PANELSPACERBACKERDOOR / DRAWER / GRILLETOP VIEWSCABINETRYIllus. A Illu

Model WS-30 Installation 51subzero.comDual InstallationsDUAL FLUSH INSET INSTALLATIONSInstalling two models WS-30 or a model WS-30 andbuilt-in unit si

Model WS-30 Installation 52Flush Inset Panels—Dual InstallationWhen installing two models WS-30 or a model WS-30 andbuilt-in unit side by side in a fl

Model WS-30 Installation 53subzero.comSide PanelsIMPORTANT NOTE: Side panels will need to be installedbefore the unit is placed in its final position.

Installation Checklist 54Complete the InstallationFor framed, overlay and flush inset applications, followthese steps to complete the installation. Be

Service Information 55Service InformationIf service is necessary, maintain the quality built into yourSub-Zero unit by calling a Sub-Zero authorized s

SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.78207011714 REV-A 7/2010

Models 424 and 424FS Installation 6Electrical RequirementsFor models 424 and 424FS, the electrical supply shouldbe located within the shaded area show

Models 424 and 424FS Installation 7subzero.comElectrical RequirementsHOME ALARM SYSTEMIf a home alarm system is to be used, refer to home alarmconnect

Anti-Tip Bracket InstallationMODEL 424FSIf you are installing the model 424FS in a space deeperthan 245/8" (625), the anti-tip bracket must be in

Anti-Tip Bracket InstallationWOOD FLOOR APPLICATIONSUse the four #12 x 21/2" wood screws and the four1/4"flat washers provided. Drill pilot